2024 ASTEC 33-36150

2024

New

3 UNITS AVAILABLE MAIN CONVEYOR EQUIPPED AS FOLLOWS: FRAME – 80’ (24.4 m) long c/c with 70” (1780 mm) deep frame UNDERCARRIAGE – Heavy duty v-type with twin cylinder raise and cylinder covers; 10 HP (7.5 kW) electric / hydraulic power pack to operate lift cylinders, power travel drives and extendable conveyor travel; Axle – gullwing axle assembly. Includes: walking beam travel axle with eight (8) 11-22.5 tires, four (4) 385/65D-19.5 radial travel tires, less cylinders. A stiff arm shall be provided in place of the fold down cylinders. King pin, air brakes, travel, brake and directional lights, mud flaps, hydraulic planetary power travel drives for two wheel drive, cam arm-style rear undercarriage to maintain constant wheel radius when raising and lowering conveyor; A center heavy duty tow eye is included for positioning within the pit DRIVE ASSEMBLY – Head end, v-belt drive for 425 FPM (2.2 m/s) belt speed Capacity – 850 TPH (770 MTPH) of 100 pcf (1.6 T/m3) material Motor – 30 HP (22 kW) electric, 1800 RPM, TEFC 3/60/460, with starters & wiring Reducer – Class I, Dodge TA5215 shaft mount Backstop – Internal type in reducer PULLEYS Head Pulley – 16” (406 mm) grooved rubber lagged, Dodge bearings; Tail pulley – 14” (356 mm) steel wing, Dodge bearings TAKE-UP – screw type IDLERS - CEMA “B” 5” (127 mm) diameter, steel roll, sealed for life ball bearings Load Area Idlers – 20 degree close spaced under receiving trough Troughing Idlers – 35 degree on 4’ (1220 mm) spacing Return Idlers – flat rolls on 8’ (2440 mm) spacing RADIAL RECEIVING HOPPER – (Rock box style) 6’ (1830 mm) long with adjustable rubber flashing ANCHOR PIVOT – Anchor pivot for radial travel BELT – Grade 2, 2 ply, 220 PIW, 3/16” (5 mm) x 1/16” (1.5 mm) mechanical fasteners EXTENDABLE CONVEYOR EQUIPPED AS FOLLOWS: FRAME – 74’ (22.5 m) long with 54” (1370 mm) deep truss with head section EXTENDABLE CONVEYOR – extendable conveyor moves in and out with a cable and hydraulic winch system (winch located in main frame conveyor) to extend the conveyor to 150 feet (46 m) DRIVE ASSEMBLY – Head end, v-belt drive for 630 FPM (3.2 m/s) belt speed Capacity – 850 TPH (770 MTPH) of 100 pcf (1.6 T/m3) material Motor – 30 HP electric, 1800 RPM, TEFC 3/60/460, with starters & wiring Reducer – Class I, Dodge TA4207 shaft mount Backstop – Internal type in reducer PULLEYS Head Pulley – 16” (406 mm) grooved rubber lagged, Dodge bearings; Tail pulley – 14” (356 mm) steel wing, Dodge bearings TAKE-UP – screw type IDLERS - CEMA “B” 5” (127 mm) diameter, steel roll, sealed for life ball bearings Troughing Idlers – 35 degree on 4’ (1220 mm) spacing Return Idlers – flat rolls on 8’ (2440 mm) spacing BELT – Grade 2, 2 ply, 220 PIW, 3/16” (5 mm) x 1/16” (1.5 mm) mechanical fasteners ELECTRICAL - NEMA 4 (IP65) enclosure with main disconnect mounted on the rear undercarriage member; all starters and wiring to motors; start/stop pushbuttons for main conveyor motor, extendable conveyor motor, hydraulic power pack motor; Cord holders and supports for power cable; LESS power cable – 460 volt, 3 phase, 60 hertz power required MANUAL CONTROL SYSTEM –the following hydraulic functions are manually controlled by switches on the electrical panel: power radial travel; conveyor raise and lower; extend and retract the telescoping conveyor section PAINT – Two part urethane primer, two part urethane topcoat – Factory standard color(s). OPTIONAL EQUIPMENT INCLUDED IN STOCK UNIT CEMA C Idlers vs. CEMA B Belting Grade 2, 3 ply, 330 PIW, 3/16” (5 mm) x 1/16” (1.5 mm) covers vs. standard Belt Cleaners (2) – Martin with tensioner Manual Landing Jacks (pin lock design) Wizard Touch Automated Control System - Includes touch screen PLC operation allows for either factory pre-set or operator in-put parameters to control the power travel, conveyor raise and lower and telescoping of the extendable conveyor; radial travel limit switches and rotat