2025 SUPERIOR 36” X 100’ PORTABLE RADIAL STACKING CONVEYOR
CONVEYOR FRAME
- MAIN FRAME: 30”DEEP TRUSS
- CHORD ANGLES: 3” X 3” X ¼”
- LATTICE MEMBERS: 1-1/2” X 1-1/2” X 3/16”
DRIVE SPECIFICATIONS
- DRIVE: CLASS I HEAD END
- GEAR REDUCER: SHAFT MOUNT
- BACKSTOP: INSTALLED IN REDUCER*
- MOTOR: 40 HP TEFC
- V-BELT DRIVE: WITH DRIVE GUARD
- CAPACITY: 750 STPH OF 100 PCF MATERIAL, 25° SURCHARGE (90% FINES, 10% SPHERICAL LUMPS, 6” MINUS)
- BELT SPEED: 400 FPM
- DRIVE PULLEY: 18” DIAMETER, 3/8” HERRINGBONE LAGGED DRUM
- TAIL PULLEY: 16” DIAMETER, CEMA CHEVRON® WING
- HEAD PULLEY: NOT APPLICABLE
- SNUB PULLEY: NOT APPLICABLE
- SHAFTS: TURNED AND POLISHED
- BEARINGS: INCLUDED
- TAKE-UP: SCREW TYPE
PORTABILITY
- CONVEYOR SPLICE: MANUAL TOP FOLDING HEAD SECTION*
- UNDERCARRIAGE: MANUAL RAISE WITH PIN LOCK ADJUSTMENT
- AXLE TYPE: TELESCOPING AXLE, ROAD PORTABLE
- TRANSPORT AXLE: DUAL (4) 11R-22.5 TIRES AND WHEELS
- RADIAL AXLE: MANUAL SWIVEL BOXES
- RADIAL TRAVEL: MANUAL
- FIFTH WHEEL: NOT INCLUDED
- ANCHOR PIVOT: MAINTAINS TAIL END DURING RADIAL TRAVEL*
- BRAKES: NOT INCLUDED
- LIGHTS: NOT INCLUDED
- MUD FLAPS: NOT INCLUDED
- AXLE JACKS: NOT INCLUDED
- LANDING GEAR: NOT INCLUDED
- TOWING EYE: PINTLE HITCH TYPE
CONVEYOR COMPONENTS
- BELTING: 2-PLY 3/16 X 1/16 2200PIW
- BELT SPLICE: FACTORY VULCANIZED BELT SPLICE*
- SCRAPERS: SUPERIOR CLICK TENSIONING EXTERRA® PRIMARY BELT SCRAPER*
- IDLERS: CEMA B, 5” DIA. STEEL ROLLS, SEALED FOR LIFE BALL BEARINGS
- IDLER SEAL: SUPERIOR STANDARD SPINGUARD® SEAL
- LOAD AREA: 20° TROUGH, STEEL ROLLS, 12-16” SPACING
- TROUGH: 35° TROUGH, STEEL ROLLS, ON 4’ SPACING
- RETURNS: FLAT STEEL CANS ON 10’ SPACING
- RADIAL RECEIVING HOPPER: SLOPED, 5' LONG, BOLT ON DESIGN*
- RADIAL HOPPER LINER: NOT INCLUDED
- GATHERING TROUGH: 5’ LONG WITH ADJUSTABLE RUBBER FLASHING
ADDITIONAL SPECIFICATIONS
- GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER RESPONSIBLE TO HAVE GUARDING INSPECTED
- SAFETY HANDRAIL: BOLTED TO IDLER FRAMES, COVESR BELT UP TO 8' WHEN RAISED
- VOLTAGE: 480 V / 3 PH / 60 HZ - 1800 RPM
- CORD HOLDERS: (1) SET BENT PIPE STYLE
- CONTROL PANEL PLATE: NOT INCLUDED
- CONTROL PANEL: CONTROL PANEL AND WIRING NOT INCLUDED
- PAINT: 1 COAT PRIMER, 1 COAT FINISH ENAMEL GRAPHITE GRAY
- GUARD PAINT: YELLOW
- IDLER PAINT: POWDER COATED SUPERIOR ORANGE
*Monthly payment stated above assumes a secured commercial use loan transaction available for highly qualified commercial loan applicants. Actual loan payment amount and terms may vary. Consumer financing not available for consumers residing in Nevada. Additional state restrictions may apply. Equal opportunity lender. Click here for more state licenses and disclosures. NMLS ID: 1857954. VERMONT RESIDENTS: THIS IS A LOAN SOLICITATION ONLY. CurrencyFinance IS NOT THE LENDER. INFORMATION RECEIVED WILL BE SHARED WITH ONE OR MORE THIRD PARTIES IN CONNECTION WITH YOUR LOAN INQUIRY. THE LENDER MAY NOT BE SUBJECT TO ALL VERMONT LENDING LAWS. THE LENDER MAY BE SUBJECT TO FEDERAL LENDING LAWS. CALIFORNIA RESIDENTS: Financing provided or arranged by Express Tech-Financing, LLC dba Currency pursuant to California Finance Lender License #60DBO54873
Your current browser cannot run our content, please make sure your browser is fully updated or try one of the browsers below.
Get Financing
