SUPERIOR 48" X 65' PORTABLE RADIAL STACKING CONVEYOR EQUIPPED AS PER BELOW:
CONVEYOR FRAME:
- MAIN FRAME: 36" DEEP TRUSS
- TOP CHORD ANGLES: 3" X 3" X 5/16"
- BOTTOM CHORD ANGLES: 5" X 3" X 1/2"
- LATTICE MEMBERS: 2" X 2" X 3/16"
- FULL IDLER RAIL BW+16", RECESSED IDLER DESIGN
DRIVE SPECIFICATIONS:
- DRIVE: CLASS I HEAD DRIVE
- GEAR REDUCER: SHAFT MOUNT RIGHT ANGLE SUMITOMO GEAR REDUCER
- BACKSTOP: INSTALLED IN REDUCER
- MOTOR: 30 HP TEFC
- CAPACITY: 700 STPH OF 100 PCF RIP RAP MATERIAL (12"MATERIAL DROPPING 3' ONTO
CONVEYOR)
- BELT SPEED: 220 FPM
- DRIVE PULLEY: 18" DIAMETER, 3/8" HERRINGBONE LAGGED DRUM
- TAIL PULLEY: 16" DIAMETER, CEMA CHEVRON® WING
- SHAFTS: TURNED AND POLISHED
- BEARINGS: INCLUDED
- TAKE-UP: SCREW TYPE (LIKE SLIDE STAC)
PORTABILITY:
- CONVEYOR SPLICE: ONE PIECE FRAME
- UNDERCARRIAGE: MANUAL RAISE WITH PIN LOCK ADJUSTMENT
- AXLE TYPE: TELESCOPING AXLE, ROAD PORTABLE
- TRANSPORT AXLE: DUAL (4) 11R-22.5 TIRES AND WHEELS
- RADIAL AXLE: MANUAL SWIVEL BOXES
- RADIAL TRAVEL: MANUAL
- FIFTH WHEEL: FOR ROAD TRAVEL, BOLT ON DESIGN
- ANCHOR PIVOT: MAINTAINS TAIL END DURING RADIAL TRAVEL, FOR 5TH WHEEL
- BRAKES: COMPLETE AIR BRAKE PACKAGE
- LIGHTS: BRAKE AND DIRECTIONAL SIGNALS
- MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS
- AXLE JACKS: NOT INCLUDED
- LANDING GEAR: MANUAL PIN ADJUSTMENT
- TOWING EYE: PINTLE HITCH TYPE
- CORD HOLDERS: INCLUDED
- LIFTING EYES: LIFTING EYES AT HEAD, TAIL, AND MIDPOINT
- SUPPORT LEGS: ADJUSTABLE HEIGHT FOLDING LEGS AT TAIL
CONVEYOR COMPONENTS:
- BELTING: MAXX TUFF 3-PLY 3/8 X 1/8 600PIW HAR
- BELT SPLICE: FACTORY VULCANIZED BELT SPLICE
- SCRAPERS: SUPERIOR CLICK TENSIONING EXTERRA® PRIMARY BELT SCRAPER
- IDLERS: CEMA D, 5" DIA. SEALED FOR LIFE BALL BEARINGS
- IDLER SEAL: SUPERIOR STANDARD SPINGUARD SEAL
- LOAD AREA: 20 DEGREE TROUGH, SUPERIOR 5' IMPACT BED MEDIUM DUTY
- TROUGH: 20 DEGREE TROUGH, STEEL ROLLS, ON 3' SPACING
- RETURNS: FLAT RUBBER DISC ROLLS ON 10' SPACING
- RADIAL RECEIVING HOPPER: SLOPED, 5' LONG, BOLT ON DESIGN BUIT WITH 1" A36
REINFORCED PLATE WORK
- GATHERING TORUGH: 1" THICK CANOE LINERS, SLOPED TOP STYLE, IN HOPPER AREA,
FULL LENGTH 1/4" STEEL ROCK GUARDS, (NO RUBBER FLASHING), BOLT ON, 36" WIDE
ADDITIONAL SPECIFICATIONS:
- IDLER NIP GUARD: FULL LENGTH NIP GUARDS
- SIDE GUARDS: FULL LENGTH SIDE GUARDING
- SAFETY HANDRAIL: NOT INCLUDED
- VOLTAGE: 480 V / 3 PH / 60 HZ - 1800RPM
- CONTROL PANEL PLATE: INCLUDED
- PAINT: SUPERIOR CLASS I - 1 COAT PRIMER, 1 COAT FINISH ENAMEL GRAPHITE GRAY
- GUARD PAINT: YELLOW
- NO ELECTRICAL SWITCHGEAR PANEL ONLY 150' OF MAIN POWER CORD WITH HUBBELL PLUG
- GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING INSPECTED
*Monthly payment stated above assumes a secured commercial use loan transaction available for highly qualified commercial loan applicants. Actual loan payment amount and terms may vary. Consumer financing not available for consumers residing in Nevada. Additional state restrictions may apply. Equal opportunity lender. Click here for more state licenses and disclosures. NMLS ID: 1857954. VERMONT RESIDENTS: THIS IS A LOAN SOLICITATION ONLY. CurrencyFinance IS NOT THE LENDER. INFORMATION RECEIVED WILL BE SHARED WITH ONE OR MORE THIRD PARTIES IN CONNECTION WITH YOUR LOAN INQUIRY. THE LENDER MAY NOT BE SUBJECT TO ALL VERMONT LENDING LAWS. THE LENDER MAY BE SUBJECT TO FEDERAL LENDING LAWS. CALIFORNIA RESIDENTS: Financing provided or arranged by Express Tech-Financing, LLC dba Currency pursuant to California Finance Lender License #60DBO54873
Your current browser cannot run our content, please make sure your browser is fully updated or try one of the browsers below.
Get Financing
