2026 SUPERIOR 36X80PRSC-S

2026

2834687

New

E00073543

SUPERIOR 36" X 80' SELF - CONTAINED PORTABLE RADIAL STACKING CONVEYOR EQUIPPED AS PER BELOW: CONVEYOR FRAME: MAIN FRAME: 30" DEEP TRUSS CHORD ANGLES: 3" X 3" X 1/4" LATTICE MEMBERS: 1-1/2" X 1-1/2" X 3/16" DRIVE SPECIFICATIONS: DRIVE: SELF-CONTAINED DIESEL / HYDRAULIC ENGINE: YANMAR TIER 4(F), 49 HP DIESEL FUEL TANK: 78 GALLON PUMP: TANDEM GEAR PUMP AND RESERVOIR HYDRAULIC TANK: 120 GALLON MOTOR: HYDRAULIC DRIVE, WITH START/STOP CONTROL VALVE AND FLEX COUPLING CAPACITY: 500 STPH OF 100 PCF MATERIAL, 25 DEGREE SURCHARGE (90% FINES, 10% SPHERICAL LUMPS, 4" MINUS) AT 18 DEGREES MAXIMUM INCLINATION: 21.5 DEGREES BELT SPEED: 400 FPM DRIVE PULLEY: 14" DIAMETER, 3/8" HERRINGBONE LAGGED DRUM TAIL PULLEY: 12” DIAMETER, CEMRA CHEVRON WING SHAFTS: TURNED AND POLISHED BEARINGS: INCLUDED TAKE-UP: SCREW TYPE PORTABILITY: POWER FOLD: HYDRAULIC TOP FOLDING HEAD SECTION UNDERCARRIAGE: HYDRAULIC RAISE AXLE TYPE: FIXED WIDTH AXLE, ROAD PORTABLE TRANSPORT AXLE: DUAL (4) 11R-22.5 TIRES AND WHEELS RADIAL AXLE: MANUAL SWIVEL BOXES RADIAL TRAVEL: 2 HP HYDRAULIC FIFTH WHEEL: FOR ROAD TRAVEL, BOLT ON DESIGN ANCHOR PIVOT: MAINTAINS TAIL END DURING RADIAL TRAVEL BRAKES: COMPLETE AIR BRAKE PACKAGE LIGHTS: BRAKE AND DIRECTIONAL SIGNALS MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS AXLE JACKS: HYDRAULICALLY RAISE AXLE TO EXTEND & SWIVEL WHEELS LANDING GEAR: HYDRAULIC ADJUSTABLE LANDING GEAR TOWING EYE: PINTLE HITCH TYPE CONVEYOR COMPONENTS: BELTING: 3-PLY 3/16 X 1/16 330PIW BELT SPLICE: FACTORY VULCANIZED BELT SPLICE SCRAPERS: SUPERIOR CLICK TENSIONING EXTERRA PRIMARY BELT SCRAPER IDLERS: CEMA C, 5" DIA. SEALED FOR LIFE BALL BEARINGS IDLER SEAL: SUPERIOR STANDARD SPINGUARD SEAL LOAD AREA: 20 DEGREE TROUGH, STEEL ROLLS, 12-16" SPACING TROUGH: 35 DEGREE TROUGH, STEEL ROLLS, ON 4' SPACING RETURNS: FLAT STEEL ROLLS ON 10' SPACING GATHERING TROUGH: 5' LONG WITH ADJUSTABLE RUBBER FLASHING RADIAL RECEIVING HOPPER: SLOPED, 5' LONG, BOLT ON DESIGN HOPPER LINER: NOT INCLUDED EXTENDED HOPPER: 12' WIDE, 10.5' TALL, 2 HYDRAULIC FOLDING HOPPER DESIGN FOR LOADER FED. ATTACHED BY BOLT FLANGE TO CONVEYOR, CAN UNBOLT HOPPER AND ROTATE 90 DEGREES RIGHT AND LEFT FROM CENTER POSITION THEN BOLT DOWN TO ALLOW LOADING ON EITHER SIDE OR OVER TAIL ADDITIONAL SPECIFICATIONS: SIDE GUARDING: SIDE GUARDING UP TO 8' INCLUDING THE IDLER CONTROL PANEL PLATE: BRACKET ONLY FOR PANEL AND HYDRAULIC LEVERS PAINT: SUPERIOR CLASS I - 1 COAT PRIMER, 1 COAT FINISH ENAMEL GRAPHITE GRAY GUARD PAINT: YELLOW IDLER PAINT: POWDER COATED SUPERIOR ORANGE OWNER'S MANUAL: (1) COPY IN ENGLISH INCLUDED FOR OPERATION AND MAINTENANCE GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING INSPECTED