2018 CATERPILLAR D8T

2018

8,595

FMC01230

Used

D2380

Caterpillar D8T with 28" Track Shoes, CAT Semi U Blade w/ Tilt, Winch is Available - Extra, Flood Light Arrangement, Engine Air Pre-Cleaner, High Speed Oil Change and Reversing Fan. CAT D8T Crawler Dozer featuring: • CAT C15 ACERT Engine • Engine Block Heater • Powershift Transmission • Cab (ROPS) w/ A/C • Differential Steer • 28" Track Shoes • CAT Semi U Blade w/ Tilt • Wear package installed at 7,900 Hours • Angle Blade w/ Tilt - 208" Wide - Available • Ripper is Available - Extra • Winch is Available - Extra • Rear Screen • High Speed Oil Change • Engine Air Pre-Cleaner • Reversing Fan • Top Carrier Rollers • Flood Light Arrangement • Rear View Camera • Rated at 364 HP • Weight 82,000 LBS When this D8T Dozer arrived in yard, MEL had local CAT dealer, Toromont CAT, complete the following at 7,720 Hrs: • Strip machine for power washing • CAT TA inspection • Update ECM flash files • Cut open all filters & inspect for contaminates - all clean • Service emissions system if needed (filters, DPF, spark plug, injector, etc) • Inspect magnetic plugs/screens & suction screens - all clean • Serviced engine • Check oil levels • Inspect oils for discoloration • Check for logged & active codes & repair • Check for applicable service letters • Changed engine, final drive, transmission & hydraulic oils Completed the following pressure checks to ensure within OEM spec: • Fan pressure & speed • Engine RPM high & low idle • Engine oil high & low idle pressures • Fuel pressure • Torque convertor stall speed • Full stall boost • Implement standby pressure • Transmission pump pressure • Torque inlet/outlet pressures • Torque convertor lock-up clutch • Flywheel low pressure - high/low • Transmission lube pressure - high/low • Performed clutch fill calibration • Steering system charge pressure • Brake pressure Based on inspection, CAT mechanic completed the following repairs: • Installed NEW DEF tank screen & cap • Installed NEW DEF injector • Installed NEW ARD spark plug • Installed NEW fast fill vent • Installed NEW pivot shaft oil reservoir bottle • Removed cab, torque convertor & engine from machine • REBUILT pump drive assembly • RESEALED flywheel housing • Installed NEW bottom end bearings (main, rod & thrust) with updated bearing kit • Installed NEW rear crankshaft seal • Resealed oil pan • Installed NEW engine mounts • Completed engine valve & injector set • Disassembled & inspected engine oil pump • Installed NEW engine belts • Installed NEW engine belt idler pulley • Installed NEW hoses/lines within chassis as required • Installed NEW EGR cooler pipe • Installed NEW heater valves • Installed NEW batteries & battery cables • Installed NEW service bay harness • Installed NEW a/c hoses & dryer • Resealed priority housing • Installed NEW hoses/lines as required • Installed NEW driveshaft u-joints • Installed all NEW heater hoses • Resealed outlet relief valve & suction tube • REBUILT/Resealed main hydraulic control valve • Stripped & cleaned condenser assembly & fans • Resealed blade lift cylinders Marcel Equipment completed the following repairs: • Completed required cosmetic & welding repairs • Completed required blade repairs • Replaced required blade pins & bushings • Line bored blade joints where required • Prepped machine for sandblasting & painting • Sandblasted, primed, painted & detailed • Assembled machine once completed • Greased machine This CAT D8T Tractor is Completed and Work Ready. The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning this Used CAT D8T dozer: At 7,692 hours, installed NEW main power relay At 7,080 hours, performed 1,000 hour service At 7,080 hours, installed NEW a/c compressor fan At 6,051 hours, installed NEW a/c compressor & belt At 6,026 hours, performed 2,000 hour service At 6,015 hours, REBUILT transmission At 6,015 hours, REBUILT transmission pump At 6,015 hours, REBUILT torque converter At 6,015 hours, installed NEW ARD head At 5,744 hours, installed NEW front crankshaft seal At 5,744 hours, removed, cleaned & pressure tested cooling package At 5,525 hours, cleaned DPF At 4,974 hours, performed 500 hour service At 4,412 hours, performed 2,000 hour service At 3,831 hours, performed 1,000 hour service At 3,711 hours, installed NEW DPF temp sensor At 3,711 hours, installed NEW ARD spark plug At 3,339 hours, performed 500 hour service At 2,061 hours, performed 2,000 hour service At 1,515 hours, performed 1,500 hour service At 1,071 hours, performed 1,000 hour service At 652 hours, performed 500 hour service

Enclosed